LINE THERMAL PRINTERMODEL CT-S281User’s ManualFEEDFEED
— 7 —Observe the following precautions for daily maintenance. When cleaning the printer, always turn it off and unplug it from thesupply outlet. Use
— 8 —THE TABLE OF CONTENTS1. GENERAL OUTLINE ... 91.1 Features ...
— 9 —1. GENERAL OUTLINEThe CT-S281 is a thermal line printer designed for use with a broad array ofterminal equipment including, data, POS, and kitch
— 10 —POWERFEEDERRORPAPERFEEDFEED1.2 UnpackingWhen unpacking the printer, confirm that the following are provided:● Printer: 1● AC adapter: 1● AC pow
— 11 —Item SpecificationsModel CT-S281RSU CT-S281RSECT-S281UBU CT-S281UBEPrint method Line thermal dot print methodPrint width 48 mm/384 dotsDot densi
— 12 —FEEDFEED2. EXPLANATION OF PRINTER PARTS2.1 Printer AppearancePrinter coverPower switchCover open buttonOperation panel● Printer coverPaper is
— 13 —POWERFEEDERRORPAPER● POWER LEDLights when the printer power is on and goes off when the printer power isoff. May blink or light in a special mo
— 14 —2.2 Paper Cover Inside● Auto CutterCuts the paper when software command is sent to the printer. Cutting methodcould be partial cut or full cut
— 15 —3. PREPARATION3.1 Connecting the AC Adapter and AC Power Cord1. Tu rn off the printer power.2. Plug in the cable connector of the AC adapter t
— 16 —PrinterPin Signal2TXD3RXD4RTS6 DSR7SG20 DTR3.2 Connecting Interface CablesTurn off the printer and unplug the power connector. Then follow the
This printer conforms to the following Standards:The Low Voltage Directive 2006/95/EC, formerly 72/23/EEC,the EMC Directive 2004/108/EC, formerly 89/3
— 17 —FEEDFEEDFEEDFEED3.5mmφ3.1mmφ5.7mm56mm3.3 Installing the PrinterThe printer can be installed horizontally or mounted vertically on the wall.At t
— 18 —3.4 Setting DIP Switch (Only serial interface type)DIP switch is provided only for serial interface specification.The DIP switch is located at
— 19 —Lever Position External Diameter of Paper Poll Remainder1 φ242 φ343.5 Adjusting the Paper Near-end SensorMove the paper near-end sensor lever t
— 20 —4. MAINTENANCE AND TROUBLESHOOTING4.1 Setting/Replacing Paper Rolls1. Press the cover open button down.2. Open the printer cover.3. Insert a p
— 21 —4.2 Removing Jammed Paper1. Tu rn the printer power off.2. Open the printer cover. If the cutter blade remains protruded with paperjammed, do n
— 22 —FEEDPOWERRORERRORPAPERAPER4.4 When the Printer Cover Cannot Be OpenedCutter lock error may occur with the Auto Cutter due to dropping of foreig
— 23 —4.5 Self-printingInsert paper into the printer. With the FEED button pressed and held, turn theprinter power on, keep the FEED button held for
— 24 —4.7 Error Indication● Paper-endPaper empty is detected in two steps: paper-end and paper near-end(factoryoption). It causes the PAPER LED to l
— 25 —5. OTHER5.1 External Views and Dimensions(Unit: millimeter)180105106FEEDFEEDFEEDFEED
— 26 —5.2 Manual Setting of Memory SwitchMemory switches can be set manually or by a command.For manual setting, refer to the next page.The function
IMPORTANT: This equipment generates, uses, and can radiate radio frequency energyand if not installed and used in accordance with the instruction manu
— 27 —Switch No. Setting Default Set ValuesMemory SW7-1 Baud Rate 9600 bps 1200 bps, 2400 bps, 4800 bps, 9600 bps,19200 bps, 38400 bps S
— 28 —Manual Setting of Memory Switch (Memory SW)The memory switch can be selected, changed, or written by the combination ofthree actions: pressing t
— 29 —6. Saving the setting and exiting the memory switch setting modePress the FEED button shortly to move to “Write/Factory Setting”. Thenpress and
TE74905-00F1.00E-0811Printed in Japan
— 1 —GENERAL PRECAUTIONS● Before using this product, be sure to read through this manual. After having readthis manual, keep it in a safe, readily ac
— 2 —SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTLY OBSERVEDBefore using this product for the first time, carefully read these SAFETY PRECAUTIONS.Imp
— 3 — Do not use or store this product in a place where it will be exposedto:* Flames or moist air.* Direct sunlight.* Hot airflow or radiation from
— 4 —Do not use the printer under the following conditions. A state subject to vibration or unstable state. A state with this product slanted.• Oth
— 5 —PRECAUTIONS IN HANDLING THE PRINTERPlease observe the following precautions for power source and powercord: Do not plug or unplug the power cord
— 6 —THESE LABELS INDICATE THERISK OF ANY INJURY DUE TO"HIGH TEMPERATURE" OF THEPRINT HEAD AND "SAW-TOOTHED EDGE" OF THEMANUAL CU
Commentaires sur ces manuels