Citizen CT-P293 Manuel d'utilisateur

LINE THERMAL PRINTERMODELCT-P290/CT-P291CT-P292/CT-P293User’s Manual

— 7 —Observe the following precautions for daily maintenance. When cleaning the printer, always turn it off and unplug it from thesupply outlet. Use

— 8 —THE TABLE OF CONTENTS1. GENERAL OUTLINE ...91.1 Features ...

— 9 —1. GENERAL OUTLINEThis product is a thermal panel printer to be built in a rack or the like that canbe used for a variety of applications includ

— 10 —1.2 UnpackingWhen unpacking the printer, confirm that the following are provided:● Printer: 1● Sample paper roll: 1 roll● Quick start guide: 1●

— 11 —1.3 Model ClassificationThe printer models are classified by the following designation method:CT - P290 AL U - WH - NNWiring cable

— 12 —Item SpecificationsModel CT-P290 CT-P291 CT-P292 CT-P293Print method Line thermal dot print methodPrint width 51 mm /408 dots 72 mm/576 dotsDot

— 13 —2. EXPLANATION OF PRINTER PARTS2.1 Printer AppearanceOperation panel coverManual cutter(CT-P290/CT-P292 only)Case(Front view) (Rear view)●Fron

— 14 —● InterfaceAttached power cord and wiring cable are connected.● FG terminalThe printer frame is connected to ground. Be sure to keep this wirin

— 15 —2.3 Operation Panel● FEED switchPressing this button once causes the paper to feed one line. The longer thebutton is pressed, the more paper is

— 16 —3. PREPARATION3.1 Mounting on Rack1. Insert the printer into the specified rack, etc. as shown in the following figure.2. Attach the supplied

WEEE MARK,I\RXZDQWWRGLVSRVHWKLVSURGXFWGRQRWPL[ZLWKJHQHUDOKRXVHKROGZDVWH7KHUHLVDVHSDUDWHFROOHFWLRQV\VWHPVIRUXVHGHOHFWURQLFVSURG

— 17 —3.2 Connecting Power Cord and Data Cable[In case of NN type]1. Make sure the power supply for the opposite equipment to be connected isOFF.2. P

— 18 —[In case of DC type]1. Make sure the power supply for the opposite equipment to be connected isOFF.2. Prepare the power supply that can supply t

— 19 —3.3 Opening and Closing Front Cover1. Apply your fingers onto the concaved placeslocated at the right and left sides of the frontcover and pull

— 20 —3.5 Adjusting Paper Adjust GuideBy changing the position of the paper adjust guide, narrower paper can be set.The paper adjust guide is set to

— 21 —3.6 Setting DIP SwitchTo set the DIP switch, the operation panel cover must be removed.Remove the operation panel cover by using the following

— 22 —Baud Rate (bps)Switch No. Function OFF ONSwitch No. Function OFF ONCT-P292InitialSettings1Auto cutterAvailable - OFF2 OFF3 OFF4 Spare Fixed - OF

— 23 —4. MAINTENANCE AND TROUBLESHOOTING4.1 Releasing Cutter LockDropping of foreign object, paper jam or the like in the printer may cause acutter

— 24 —4.2 Cleaning the Print Head and PlatenCAUTION! The print head is hot immediately after printing. DO NOT touch it with your hand. DO NOT touc

— 25 —4.4 Hexadecimal Dump PrintingThis function is to print all received data in hexadecimal numbers. If problemssuch as missing data, data duplica

— 26 —4.6 Error Indication● Paper endPaper empty is detected in two steps: paper near-end and paper end. It causesthe ERROR LED to light. If paper

IMPORTANT: This equipment generates, uses, and can radiate radio frequency energyand if not installed and used in accordance with the instruction manu

— 27 —(Unit: mm)CT-P290/CT-P291 (2 inch model)122127138102107118103+0.5103+0.5103+0.5123+0.510289 510.510911010258910.51091106815.52948815.5294DC type

— 28 —φ12φ1860~755 2_+4 2_+4 2_+2 2_+Paper width 58+0−1Maximum print area 51Maximum print area 72φ50 or lessPrinting surface(Unit: mm)5.2 Printing

— 29 —5.3 Manual Setting of Memory SwitchesMemory switches (Memory SW) can be set manually or by a command.For manual setting, refer to the next pag

— 30 —Switch No. Setting 0 (OFF) 1 (ON)Memory SW5-1 Reserved Fixed − SW5-2 Reserved Fixed − SW5-3 Reserved Fixed −

— 31 —2. Selecting memory switchWhen the FEED button is pressed short (within 2 seconds), printing occursin the order of “Memory SW1” → “Memory SW2” →

— 32 —5.4 Specifications of Power Supply and Interface ConnectorsConnector pin assignment for power supply, serial interface and parallelinterface is

— 33 —a. The ERROR and PE LED indicators are provided with a resistance of 330 W inthe circuit to keep the current value at 10 mA. To use this termin

ZH74902-20F1.20E-1202

— 1 —GENERAL PRECAUTIONS● Before using this product, be sure to read through this manual. After having readthis manual, keep it in a safe, readily ac

— 2 —SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTLY OBSERVEDBefore using this product for the first time, carefully read these SAFETY PRECAUTIONS.Imp

— 3 — Do not use or store this product in a place where it will be exposedto:* Flames or moist air.* Direct sunlight.* Hot airflow or radiation from

— 4 —Do not use the printer under the following conditions. A state subject to vibration or unstable state. A state with this product slanted.• Oth

— 5 —PRECAUTIONS IN HANDLING THE PRINTERPlease observe the following precautions for power source and powercord: Do not plug or unplug the power cord

— 6 —Caution label is attached on the position shown in the following figure. Carefullyread the precautions in handling before using the printer.THIS