Citizen CT-S651 Manuel d'utilisateur

LINE THERMAL PRINTERMODEL CT-S651User’s Manual

—7—CAUTIONTo prevent injury and printer failures from worsening, observe the following: While the paper cover is open, be careful to not touch the ma

—8—1. GENERAL OUTLINE...91.1 Features ...

—9—The CT-S651 line thermal printer series is designed for use with a broad arrayof terminal equipment including data, POS, and kitchen terminals.Thes

—10—Make sure the following items are included with your printer.Model numbers indicate printer features according to the following system.Note:*: AC

—11—1.4 Basic SpecificationsItem SpecificationsModel CT-S651Print method Line thermal dot print methodPrint width *1 80 mm/640 dots, 72 mm/576 dots, 6

—12—Notes:*1: When paper width is 83, 80, 60, or 58 mm.*2: The number of printable columns is selected using a memory switch.The numbers of columns no

—13—Operation panelz POWER LED (green)Lights when the power is on, turns off when the power is off.Flashes when data is incoming or a memory error has

—14—Rear connectorsz Interface connector (serial, parallel, USB, etc.)Connects to the interface cable.The serial interface board is equipped with a DI

—15—z PlatenFeeds the paper.Do not remove the platen except to do maintenance.z Paper near-end sensor (PNE sensor)Detects when the paper is near the e

—16—z Paper end sensor (PE sensor)Detects when there is no paper. Printing stops when this sensor detects thereis no paper.z Paper thickness selection

WEEE MARKEnWenn Sie dieses Produkt entsorgen wollen, dann tun Sie dies bitte nicht zusammen mit demHaushaltsmüll. Es gibt im Rahmen der WEEE-Direktive

—17—1. Turn off the power.2. z For the built-in power type printer, connect the AC power cord to the AC inlet, andinsert the plug into an electric out

—18—1. Turn off the power.2. Orient the interface cable correctly and insert it into the interface connector.3.2 Connecting Interface CablesSerial int

—19—Use a serial interface cable with the connection layout shown below.CAUTION Always unplug the AC adapter from the printer before connecting thepr

—20—1. Turn off the power.2. Confirm the orientation of the cash drawer kick-out cable connector and connect itto the cash drawer kick-out connector a

—21—(1) Connector pin configuration(2) Electric characteristics1) Drive voltage: 24 VDC2) Drive current: Approx. 1 A max. (not to exceed 510 ms.)3) DR

—22—This printer can only be positioned horizontally. It cannot be positionedvertically or on a wall.3.4 Precautions for Installing the PrinterCAUTION

—23—Set the partition to the width of the paper roll you are loading.The partition is set at the factory to the position shown below.z For 3-inch type

—24—1. Turn off the printer and unplug the power cord from the electric outlet.2. Remove the mounting screws of the serial interface board.3. Remove t

—25—Change the settings of the paper near-end sensor to set the position at whichthe near-end of the paper is detected.1. Use a pointed object, such a

—26—1. Turn on the power.2. Press up on the cover open button to open the paper cover.3. Load the paper roll so that the printable side of the paper i

Declaration of ConformityThis printer conforms to the following Standards:The Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoH

—27—Attach this cover to prevent the power switch from being used.1. Press the power switch cover onto the power switch compartment until it clicks.Pu

—28—Attach the interface cover to the back of the printer.The shape of the interface cover is different depending on the type of powersource.1. Press

—29—A dirty print head or platen may reduce printing quality or cause malfunctions.We recommend cleaning the printer periodically (every 2 to 3 months

—30—The ERROR LED flashes and the auto cutter blade remains extended because aforeign object or paper jam is obstructing it.If the ERROR LED is flashi

—31—5. Lift the protective sheet and turn the cutter gear in the direction of arrow B to returnthe auto cutter to a position where the paper cover can

—32—While paper is loaded, press and hold the FEED button while turning the poweron. Hold the FEED button down for about one second and then release i

—33—Print received data in hexadecimal. If problems such as missing or duplicateddata occur, this function allows you to check whether or not the prin

—34—z Paper-endThe end of the roll of paper is detected at two stages, paper near-end andpaper-end.When paper near-end is detected, the PAPER LED ligh

—35—The status display for various messages is shown below.Notes:*1: If the paper cover or front cover is open in standby.*2: If the paper cover or fr

—36—(Unit: mm)5. OTHER5.1 External Views and DimensionsBuilt-in power supply typeAC adapter type19231145140 1551614219231145114

—1—GENERAL PRECAUTIONSz Before using this product, be sure to read through this manual. Afterhaving read this manual, keep it in a safe, readily acce

—37—Use the paper shown in the following table or paper of the same quality.(Unit: mm)5.2 Printing PaperPaper type Product nameRecommended thermal rol

—38—Memory switches are used to set various printer settings. The memory switchescan be set manually (set by hand on the printer) or by commands. This

—39—Individual setting modeSet the memory switches individually.Do the settings while confirming the memory switch function and settings onthe printou

—40—5. Press the FEED button for at least two seconds.A setting for the memory switch is printed, through the cycle, each time the FEEDbutton is press

—41—The function of each memory switch is shown in the following table. (Shadedvalues are factory settings.)Switch no. Function OFF ONMSW1-1 Power ON

—42—Notes:*1: If print data is very dense, the print head is hot, data transmission is slow, or some otherconditions, the motor and printing may occas

TZ74948-00FA02053E-1004

—2—Before using this product for the first time, carefully read these SAFETY PRECAUTIONS.Improper handling may result in accidents (fire, electric sho

—3—PRECAUTIONS ON PRINTER INSTALLATIONWARNING Do not use or store this product in a place where it will be exposed to:* Flames or moist air.* Direct

—4—CAUTIONDo not use the printer under the following conditions. Avoid locations subject to vibration or instability. Avoid locations where the prin

—5—PRECAUTIONS IN HANDLING THE PRINTERWARNINGPlease observe the following precautions for power source and powercord: Do not plug or unplug the power

—6—CAUTIONCaution label is attached in the position shown in the following figure. Carefully readthe handling precautions before using the printer.